Saturday, 4 December 2010

NetworkStudies.co.uk

NetworkStudies.co.uk

For a while now I've been a little unsettled at using the domain ciscostudies.co.uk particularly after Jeremy Cioara's experience of looking down the business end of Cisco's legal department.

So, I've moved. From now on my study notes, thoughts, and helpful hints will be located at www.networkstudies.co.uk :o)

Cisco - Catch me if you can!

See you there...

Thursday, 2 December 2010

New home for Jeremy Cioara...

Where is Jeremy?...

I'm busy tidying things up before I start my series of notes on CCNP Switch and I thought I'd check in with Jeremy, so I go to his ammended blog www.ciskoblog.com and low and behold I'm redirected to http://www.tekcert.com

It's been a while since I last took a look at what the Master had to say so I'll be spending some time here over the next few days seeing what's what.

Keep up the good work Jeremey :o)

Tuesday, 26 October 2010

Subnet Mask vs Wildcard Mask

Something I find I struggle with is when to use a subnet mask and when to use a wildcard mask. This article is to simply set out the instances when you will use one or the other (not the actual steps to apply them).

Subnet Mask:

  • When applying an IP to an interface
  • Routing protocol summary addresses
  • BGP
  • PIX security appliance ACL's
  • ASA security appliance ACL's
  • When creating DHCP pools on a Switch or Router

Wildcard Mask:
  • EIGRP network statements
  • OSPF network statements
  • VPN concentrator network lists (when setting the local and remote allowed networks)
  • Router ACL's
This list is not exhaustive and I will add to it as I come across new instances where you use either a Subnet mask or Wildcard mask. 

Friday, 17 September 2010

BSCI Exam - Passed!

Well, I've just got back from the test centre and I'm pleased to say that I passed!!

It was a bit touch and go though as I think there was about 1 minute 30 seconds left on the clock.

No rest though as I've already started CCNP SWITCH at my local Cisco Networking Academy.

As you'll guess, most posts from now on will be SWITCH related.

Thanks
Jonathan

Wednesday, 15 September 2010

BSCI - OSPF - Adjacency requirements

For an OSPF adjacency to form the 2 neighbors must agree on several parameters within the Hello Packet before the adjacency can form. These are:

i) Each must have a unique Route-ID
ii) Each must be in the same Area
iii) Authentication setting must match
iv) Timers must match.

One other parameter that must be agreed upon is the router priority for DR/DBR elections.

BSCI - Manipulating Routing Updates - Route-map permissions

When compiling a Route-map(RM), you set an access control list (ACL) then use the Route-map to match addresses set out in that ACL to apply your chosen criteria in the Set field of the Route-map.

Now the question is given the combination of permit or deny statements in the ACL and the permit or deny statement of the Route-map what is the out come for a packet.

The following is what happens to a given packet when the permit or deny statements are considered:

ACL = Permit
RM= Permit
Result = Packet Permitted to proceed via the route-map. That's to say the packet is permitted to be permitted.

ACL = Deny
RM = Permit
Result = Packet Denied. The packet is denied from being permitted.

ACL = Permit
RM = Deny
Result = Packet Denied. The packet is permitted to be denied.

ACL = Deny
RM = Deny
Result = Packet PERMITTED. The packet is denied from being denied. If it isn't allowed to be denied, it must, therefore, be permitted.

Bit of a weird one to get your head round but it's an obvious trick to chuck in there when you're under pressure so keep an eye out.

Tuesday, 14 September 2010

BSCI - IPv6 - IP address types

The following is a list of IPv6 address types. The high order bits are displayed and their function:

i) 001 = Global - 200
ii) 1111 1111 = Multicast - FF
iii) 1111 1110 11 = Site Local - FEC0
iv) 1111 1110 10 = Link Local - FE80
v) ::X:X:X:X = IPv4 compatible address, where the first 96 bits are set to 0 (hence the ::) and the remaining 32 bits are converted to hex from the IPv4 address

Other addresses include:
::1 or 0:0:0:0:0:0:0:1 = Loopback
::/128 = unspecified address which is essentially the DFG for IPv6, all the bits are set to 0.
IPv6 private addresses start - 1111 1110 1 - therefore both site local and link local are private

BSCI - EIGRP - Adjacency Requirements

The following criteria need to be meet before an EIGRP adjacency will form:
i) Authentication (if in place)
ii) AS Number
iii) Source IP MUST be the primary address for the interface - secondary IP's will not result in the adjacency forming
iv) K values must match

N.B. - Timers do not have to match but they must be equal.
- Adjacency will flap if timers are mismatched.
- Therefore ensure you have a reliable time source.

BSCI - ISIS - Adjacency requirements

For an ISIS adjacency to come up the following criteria must match:
i) MTU  - default is 1497
ii) Router Levels - L1, L1/L2, L2 only
iii) If L1 router, the IS must be in the same area
iv) System ID's must be unique
v) Authentication (if used)

Adjacency is formed after a 3-way handshake. The stages are DOWN - INIT- UP

The adjacency is up if the neighbor has put you identity in their hello packet.

BSCI - ISIS - Show commands

The following show commands can be used for ISIS:

#sh ip protocols
-Displays: active interfaces, routing information sources (neighbors), whether summarisation is in effect, last update

#sh clns protocols
-Displays: System ID, ISIS router type (L1| L1/L2| L2), Area IS, active interfaces

#sh clns neighbor
-Displays:  Single Line summary of neighbors, system id NAMES, SNPA, State (Up or Down), hold time, router type, protocol

#sh clns neighbor detail
- Displays: multi-line details of neighbors, neighbor info, Area ID, up time, ip of neighbor

#sh isis database
-Displays:  L1/L2 routers you see 2 Db's, * indicates the DIS (which is elected either via the interface cmd #isis priority [number] or is a priority is not set the DIS is the device with the highest SNPA which in this case it the Ethernet MAC address on the router)

#sh isis topology
- Displays: system, metric, next-hop, egress interface to get to next-hop, SNPA of next-hop router